| || |
Article completely revised November 2015
Stainless steel is much harder than carbon steel and consequently is more time–consuming to sharpen. Both stainless and carbon steel knives hold a good edge if sharpened correctly. Factory made knives usually need sharpening before use, sometimes they have been ground to the correct angle with a flat primary edge but the final sharpening angle is up to the buyer. Always sharpen your new knife when you buy it so it is ready for use when you need it; this is even more important if you have never tried sharpening a knife before. If your efforts result in a knife that is blunter than when you bought it, you are getting the technique wrong. It is always best to learn in the warmth and comfort of your own home; keep a couple of first aid plasters to hand! If the crunch comes and you get into a survival situation, the last thing you want to do is sit down in a blizzard or pouring rain and sharpen your knife before constructing that vital shelter or skinning that delicious rabbit, only to find you cannot do it.
A knife can be sharpened on any stone that is harder than steel using the correct technique, the problem is finding such a stone in a survival situation. It is wise to carry a sharpening stone in your survival kit and there are many small models available in most countries. In North America, I would choose EXE–LAP. In Europe, I would choose the Fällkniven DC3 (photo, above) or the larger DC4; widely available is the Spyderco ceramic sharpener. None of these stones requires lubrication. For sharpening a survival knife, buy a 600–grit diamond stone or equivalent. A course stone will work faster but the medium grade will give a sharper, longer lasting edge. Some stones have a medium grit and a fine grit side. Use the fine grit side to polish the sharpened edge and it will be more durable. In the field, consider carrying a pen sized, Gerber Diamond Knife Sharpener (photo, right). Not as effective as a stone but it can put an edge on a blade relatively fast if the blade just requires a bit of toning up and this is most common for a survival knife. If you use your knife for chopping wood, this will quickly blunt the edge, so after building your shelter and cooking your rabbit, relax before nightfall with your sharpening stone and restore the edge on your knife. After using an abrasive stone, a couple of light strokes with a Gerber Diamond Knife Sharpener can remove unwanted metal left by grinding (burr). I use a medium abrasive stone and then finish off with a fine grit to polish the edge, a few strokes down the Gerber Diamond Knife Sharpener leaves a durable, sharp edge.
Oil stones are the traditional Western stones that many people grew up using. These stones are made from one of three materials (Novaculite, Aluminium Oxide, or Silicon Carbide) and use oil for swarf (metal filing) removal.
The most traditional oil stones are natural stones made from Novaculite. These natural stones are quarried in Arkansas and processed to make what we call Arkansas Stones. These stones are separated into different grades related to the density and the finish a stone produces on a blade. The coarsest of them are called Washita. The Washita is not often used these days because it is very soft. The finer grades are called Soft Arkansas, Hard Arkansas, Hard Black Arkansas and Hard Translucent Arkansas. These natural oil stones can produce a polished edge, but tend to cut more slowly than man-made stones. The Hard Black Arkansas and Hard Translucent are more rare and are therefore more expensive.
The Aluminium Oxide oil stones are a very popular man made choice. The most popular are called India Stone which are made by Norton. These stones can cut fast, and can also produce a fine edge on tools and knives. The grading system for these stones is generally labelled fine, medium, and coarse. These stones are often brown or orange in colour. When compared with the Arkansas stones, Aluminium Oxide (India Stones) are more coarse. The India Stones are used in conjunction with Arkansas Stones to cover all levels of coarseness.
The fastest cutting oil stones are made of Silicon Carbide. The silicon carbide stones made by Norton are called Crystolon stones. These stones are also labelled fine, medium, and coarse. They are usually grey in colour. While these stones will not produce an edge as fine as the India or natural stones, the fast cutting makes them ideal for initial coarse sharpening. Because they sharpen quickly, it a common practice to use the Coarse Crystolon and then progress to an India Stone and then to finish up on an Arkansas Stone.
The good overall performance and the lower price are the oil stone's greatest assets. A set of India or Crystolon stones are the least expensive stones to purchase. The natural Arkansas Stones vary in price from the very economical Soft Arkansas to the more expensive Hard Black and Translucent Arkansas Stones. These stones are also relatively hard, so the stones rarely require flattening.
The main disadvantage of the oil stone is its slower cutting rate. Of the three main stone types, the oil stone is the slowest. The fact that oil is used to remove the swarf is also messier to clean up than water.
Water stones are relatively new to the Western world, but have gathered a large following due to their many advantages. Like the oil stones, the water stones are available in both natural and synthetic materials. However, due to availability, only synthetic stones will be discussed.
Synthetic water stones are generally made of Aluminium Oxide. This is the same abrasive material used in the India stones. However, the difference between the two is the binder that holds the abrasives in the water stone together. Water stones are softer than India stones, which promotes faster cutting because the old abrasive material breaks away and is replaced with fresh sharp material.
Fast cutting is clearly an advantage of the water stone. The other obvious advantage is the use of water rather than oil to remove the swarf from the stone. However, the water stone is not perfect. The softness that promotes fast cutting also wears the stone down more quickly. This tends to wear the stone unevenly, which requires flattening to bring the stone back into shape.
Diamond stones contain small diamonds attached to the face of a metal plate. These small industrial diamonds are much harder than any of the other sharpening stones. However, not all diamond stones perform the same function, nor are they always created equal.
There are two main types of diamond stone styles. The more common style contains holes in the diamond surface to capture the swarf. These stones cut very fast and are very simple to use. The next type is the continuous diamond surface. These stones are preferred when you are sharpening tools with points that might get caught in the recesses of the non-continuous diamond surface. Both types of diamond stones are available in mono–crystalline and poly–crystalline diamonds. The mono–crystalline diamonds are more desirable as they will last longer.
The two greatest advantages of the diamond stone are the very fast sharpening and the flatness that is retained by the diamond stone. In fact, extra–coarse diamond stones are often used to flatten oil or water stones. The main disadvantage of the diamond stone is its initial cost. While these stones are the most expensive, they will also last a long time, so the long-term cost can be comparable to other stones.
How do you actually sharpen a knife?
Sharpening a knife is all about technique. Once you have mastered the technique you can sharpen any knife. You need a sharp edge in a survival situation — it does not have to be perfect, just "sufficient onto the day."
The poor survival knife is expected to fulfil many cutting and chopping functions and this is a lot to ask of one blade. Think about the number of knives you use in your kitchen at home in food preparation and eating. You may have to use your survival knife to chop through bone, de–scale and fillet fish, slice meat, cut down vines, slice fruit, cut Paracord, kill an animal, to name but a few uses. Add cutting brushwood, splitting branches and hacking through vegetation and you get the picture.
So how can you use one poor knife to fulfil so many functions? The answer is in the edge you produce. A thin, sharp edge ground with a narrow angle is useful for slicing and cutting but will not retain its sharpness (durability) for long if you whittle wood down with it. A thicker, wider angle edge will perform chopping and whittling functions longer without the need for sharpening but is not very effective if you want to de–scale fish. If you only have one knife, you have to learn how to regrind and sharpen it to give the edge you need for the job in hand. It makes good sense to carry two knives. Keep the drop point 15 cm (6 inch) blade for general rough work and a folding lock knife with a narrow angle and very fine edge for the more delicate jobs. Use a wire saw to cut thicker branches and poles for shelter making. Do not use your precious knives for the wrong job because a lazy moment will cost you a lot of hard work recovering the blade edge later on.
Sharpening a survival knife (both folding knife and fixed blade drop point shape)
There is not a perfect angle for a cutting edge, only the correct angle for the job you intend to do. Most people find it difficult to sharpen a knife, that is, to achieve a super sharp, durable cutting edge and the main reasons for failure are:
For larger blades, you can use both hands if more convenient: Use thumb and finger to set sharpening angle.
For smaller blades and a smaller stone, use the thumb.
Use a circular motion or push and pull the blade up and down the stone. Work the entire length of the blade; after several strokes, feel with your fingernail the edge of the side you are not sharpening to detect burr. Once you have burr down the whole length of the blade, turn it over and sharpen the other side. Keep a constant pressure when grinding by resting the knife on your thumb (or thumb and finger for longer blades) and let your thumb rub over the abrasive.
Everyone has thumbs of different sizes, so find the place on your thumb and finger to rest the blade that gives the required angle. It can take over one hundred strokes to sharpen stainless steel and less for carbon steel. The metal of the cutting edge becomes very thin as it is being ground on the abrasive block and it will form a burr where the metal turns away from the abrasive.
Once you have burr, you are on your way to a sharp edge. You can feel the burr with your thumbnail. Never run your finger down the blade, only across it, for obvious reasons. When you sharpen the other side of the blade the first few stokes will remove the burr. Once the second side forms a burr on the side you first sharpened, you have the edge. If your abrasive stone has both fine and coarse sides, give your blade a couple of light strokes over the finer abrasive to remove the burr. If you have a Gerber Diamond Knife Sharpener, use this to remove the burr, a couple of light strokes are all that is needed. It is possible to polish the cutting edge further on a leather belt using a process known as "stropping," but this is not necessary for a survival knife and somewhat impractical in the field.
Inspect the blade. If your angle is correct, both sides of the blade should be ground to the same angle. If one side looks as if more metal has been removed, then you have made the grinding angle shallower on this side and there is nothing for it but to start the process all over again. Test the edge by slicing it through paper, it should make a clean cut and not stick to the paper or tear it. If you do not have paper in a survival situation, just use the knife for the intended purpose. If it cuts the way you want it to cut, then you have a sharp knife. If it does not work as you intended, repeat the sharpening process making sure you sharpen the whole length of the blade by keeping the angle right and the pressure on the blade constant.
Sharpening serrated blades and gut hooks
Serrated blades retain their ability to cut effectively far longer than a straight edged blade, however they are much more difficult to sharpen. It is necessary to use a tapered or cylindrical fine diamond steel or ceramic and each separate serration much be sharpened individually.
Serrated blades have a grind on one side of the blade, which is the only side you sharpen. Hold the sharpener at the angle that matches the original edge angle of the knife. It is best to clamp the blade down, or hold it with the edge away from you and the serrated side of the edge facing up. Set the tapered diamond sharpener in a serration so that you fill the indentation. It helps if you mark this position on the sharpener to stop you honing too far down the taper and ruining the point on the serrated edge (see Gut Hook procedure below). Draw the sharpener towards the edge rotating or spinning it as you go; 5 –10 stokes of a fine grade hone should be sufficient. If the blade is very dull you may need to start with 5 –10 stokes of a medium grade hone, finishing with 5 – 10 stokes of a fine grade hone.
Even if you use a tapered sharpener it is almost impossible to achieve an edge that equals the original factory ground edge, but you can expect to get an edge that is good enough. A serrated blade is more easily distorted through sharpening than a straight blade edge. So, don't sharpen it unless absolutely necessary. Most hardware shops and some of the better blade makers offer a sharpening service; if you are not confident you can sharpen a serrated knife, especially an expensive one, consider paying an expert to do it for you.
The main problem is getting the angle of the grind correct. A neat trick is to paint the serration with a black marker pen (Sharpie) so you can see if you are removing all the black ink. (If the blade is blackened already use a different colour marker.) This helps you to make small corrections to your angle of grind as you work. Check it after every stroke. Do not over–sharpen the serrations and do not use too much pressure. Always start off with a fine grade hone and only use a medium grade hone if absolutely necessary as it is easy to remove too much steel very quickly, ruining the cut of the serration.
After you have honed all the serrations, feel the flat side of the blade with a finger nail. You should detect a very fine burr. If you cannot feel it, repeat the sharpening process with 5 more stokes of a fine hone on each serration until the burr is evident. Place the non-serrated side of the blade down flat on a fine diamond hone or fine whetstone and remove the burr with a couple of stokes using light pressure.
The right tools for the job
Illustrated in the photo above are Diafold serrated knife sharpeners, available in extra fine, fine and coarse grit. They taper from 6,35 mm to 1.59 mm (1/4 inch to 1/16 inch) and are 24.13 cm (9 1/2 inches) when open, 12.7 cm (5 inches) closed.
Lansy's Folding Diamond Tapered Sharpening Rod (photo above) sharpens regular and serrated blades, fish hooks, gut hooks, and many other tools. The fine (600 grit) tapered rod folds into the ergonomic nylon impregnated plastic handle for protection and ease of carrying. Length when closed 8.9 cm (3.5 inches).
There are many such sharpeners on the market, for example the Smith's Pocket Pal illustrated below, but it comes only with one grade of diamond hone.
Sharpening gut hooks
This is a similar process sharpening a serrated blade, but a gut hook is honed on both sides of the blade. Use a ceramic or diamond tapered sharpener as for serrated knives. First, place the thicker end of the sharpener in the open end of the gut hook so it is not filling the entire width of the gut hook and wrap tape around the sharpener to help you not to hone past this position. If you hone filling the entire width of the gut hook with the wide end of the sharpener it will enlarge the gut hook curve and distort the cutting edge.
Unlike sharpening a serrated knife you do not start with the wide end of the sharpener in the gut hook, position the pointed, narrow end of the sharpener up against the open end of the gut hook.
Make sure the sharpener is facing toward the thickness of the blade (away from the edge of the gut hook). Match the angle of the sharpener to the original edge angle of the knife. This will maintain the correct sharpening angle and prevent you from getting cut by the blade tip. Use 5 – 10 light stokes using medium pressure on the sharpener, stopping when you reach the tape used to mark the length of the stroke. Using a forward and sideways motion, stroke the sharpener from one side of the gut hook to the other. Spin the sharpener as you go. As with sharpening a blade edge, the objective is to start at the edge and stroke away from the edge. Do not over-sharpen or put too much pressure on the sharpening tool. Hone alternate sides and check your progress often. As with other blades you can mark the cutting edge of the hook with a permanent marker pen (Sharpie) to help you get the angle right. Examine the hook after each stroke to make sure you are removing all the ink and not going beyond the ink mark.
Knife Sharpening Systems and Kits
In this article we discuss the pros and cons of selected sharpening systems that all work. They vary only in ease of use, size and price. Sharpening systems can be categorized as follows:
The Aligner Guided Diamond Sharpener ensures guided strokes and exact bevels to give a consistent angle and produce the ultimate in fast, accurate knife sharpening. A very flexible guided sharpening system with 7–angle variability and the handle accepts any 10.5 cm (4 inches) DMT® Diamond Whetstone. The knife clamp can be used separately as a sharpening guide with any bench model DMT® Diamond Whetstone. Included is a fabric storage pouch with Velcro enclosure. Price guide £46.00 (around $73). Highly recommended piece of kit.
Manufacturer: Columbia River.
Slide Sharp uses a unique system of injection moulded nylon guides to hold the knife–edge at the specific angle required for optimum sharpening. A hardwood base holds a porcelain sharpening rod. Simply insert the rod in the base, slide a return spring over it, select the sharpening guide needed for your knife and slide on the cap. Sharpening action couldn't be easier. Just pull your blade through a sharpening guide slot pressing down lightly. The return spring pops the guide up again for the next stroke. You then repeat the same action as needed in the opposite slot, sharpening both sides of the blade equally or as needed. Two sharpening guides are included. One is a slight angle for putting an edge on sport, work, tactical and kitchen knives. The second has a steeper angle for heavier tools such as choppers and machetes. The Slide Sharp system comes with two porcelain sharpening rods. You start with the coarser grey rod and finish the edge with the fine white rod. Price guide around £25.00 ($40). Good but sizable in a 26 x 11.5 cm (10 x 4.5 inches) box.
The Smith's 3–in–1 Sharpening System is a handy sharpener you can take anywhere and it will do three jobs in one. Features pre–aligned carbides for quick edge setting, 750 grit interrupted surface diamond sharpener and pre–aligned ceramic sharpeners for sharpening standard and serrated blades. The rods easily store in the base. Price guide around £20.00 ($30).
The Tri–Angle Sharpmaker includes two sets of high Alumina Ceramic stones: A pair of medium grit (dark) stones for aggressive sharpening and a pair of fine stones (white) for professional grade finishing. There is also a set of brass safety rods to protect the user's hand during sharpening. For sharpening plain edges, the flat sides of the stones are ideal. For serrated edges, use the corners. The stones fit into keyed holes and slots moulded into the polymer base and have a 40–degree and 30–degree sharpening angle for knives and a 12.5–degree scissor setting. A groove running the length of the stone is for sharpening pointed objects like darts, awls and fish–hooks. All components pack into the base and the lid snaps shut making the 204 self–contained and small enough to carry in your shirt pocket. No lubrication is required during use for dry, mess–free sharpening. Includes instruction DVD and book. Price guide around £50.00 ($80). Good but sharpening is set to give only two possible angles.
A sharpening system that is simple – and really works! This revolutionary design, by Austrian Harald Stallegger, will guarantee a razor sharp edge after only a few swipes. This patented spring–loaded mechanism allows you to pull the blade through the hardened steel inserts along the blade surface, all the way to the tip. Vulkanus is designed to sharpen serrated blades as well. Price guide around £35.00 ($55) in plastic, around £60.00 ($95) in stainless steel. This is a really excellent sharpener and highly recommended.
The Gerber Pocket Sharpener is manufactured with coarse and fine ceramic stones set at the correct angles. Weighing only 1 oz, this will put an edge on any worn blade. Very useful field tool and the cheapest in my selection. Price guide around £4.00 ($6). Cheap and it works very well on smaller knives but not as versatile as some of the systems shown above. You pays your money and you takes your choice!
Diamond Sharpening Set
The Lansky diamond deluxe sharpening set is expensive because of the diamond stones and you need to have many knives to sharpen to justify owning one. Price around £55.00 ($87) for the professional set.
They also produce a cheaper set with hones of Alumina Oxide and Ceramic Hones (roughly half the price).
No sharpening system is 100% accurate and although the set provides sufficient guide rods to set up each hone, better results are obtained by using the same guide rod for all the hones when working down the grades. Also, more consistent results may be achieved by removing the knife from the flip-over knife clamp and turning it over (using the same side for both sides of the blade) rather than flipping the stand over and using the other side of it.
To achieve excellent results it is worth adding an Ultra–fine hone, a Super Sapphire hone and a Leather Stopping hone to your kit to achieve a highly polished and durable cutting edge. If you have a serrated knife you will also need medium and fine serrated hones.
Do not use too much pressure when sharpening the blade. If you press too hard, you take off a lot of metal and the blade has a tendency to jump out of the clamp or move around. Too much pressure, especially as you work down the grades of abrasive leaves unnecessary grinding marks that are hard work to remove with the sapphire stone. You need to find the right touch; it requires patience and a little finesse.
It works but is pricey and cheaper systems will do an equally good job. This sharpening system is really for use in the workshop to get your blades in first–class shape. In the field it is sufficient to carry the knife guide, one guide rod and the fine stone with you to keep a blade in top order. If you have a sapphire stone take that along too.
GATCO© Edgemate™ Ultimate Diamond Sharpening System
This sharpening kit is very similar to the Lansky kit and works the same way.
THIS SYSTEM CONTAINS:
The rods are prone to get loose and wobble ruining the effectiveness of the sharpener. Apply some cyanoacrylate glue on the rods, then slid the rods in a couple of centimetres (an inch or so). This forces the glue into the wobbly slots. Let the glue cure and then brake the rods free from the glue by twisting them with pliers. Once broken free, the rods still slide in and out nicely, but no more wobble, restoring the effectiveness of the honing angle.
Price: around £37.99, circa $60.00. An extra fine sharpening hone will cost you an additional £7.99, circa $12.50. A useful addition is the GATCO Easy Clamp Mount which will add a further £5.99, circa $9.00.
For price and performance this is a highly recommended sharpening system.
Manufacturer: Darex LLC
Work Sharp Guided Field Sharpener
The Guided Field Sharpener incorporates five stages of sharpening and honing, each with built in angle guides:
Our product test
We found the sharpener needed a little practice to get the best out of it, which is fair enough. The 20° honing guides assist in starting out the honing process but you still have to maintain this angle as you move the blade away from the guide down the length of the blade. Before you start, mark the edge with a marker pen (Sharpie) so you can see how well you are maintaining the angle of cut and adjust your cutting accordingly. With practice it is possible to achieve a consistent angle along the length of the blade.
We found the sharpener works very well for flat and curved blades but is less successful for serrated blades and thick blades such tactical folders and knives with a Tanto shape as the design of this blade can radically affect the angle of honing if you use the 20° honing guide.
The diamond plates are easily removed (held by magnets, watch your compass, they throw out a strong magnetic field!) and this gives flexibility for freehand, un–guided sharpening of, for example, axes, hatchets and machetes.
We found the "fine" diamond plate is a bit course and to remove the grind marks with the ceramics is a little time consuming. The leather honing strop is a good addition and works well once you have patiently worked through the course and fine ceramic rods.
The grooved ceramic rod performs well for sharpening fish hooks and the fine grit serration sharpener works OK but is no substitute for a tapered file made for the job.
In summary, good for knives that require a 20° edge and with a little care and a lot of practice the sharpener works well and incorporates a lot of flexibility in how you can use it. Not bad for one device. Well made and easy to use. The 25° guided ceramic rods and leather strop make it a useful tool for touching up a pre–sharpened blade. The course grit diamond plate takes off a lot of metal fast so do not start off with it, this is best suited to sharpening blades where the edge angle and blade profile is not so critical (such as, an axe blade or machete). The fine grit diamond plate is also quite abrasive so care is needed when using it (depending on the hardness of the blade steel), use minimum pressure and test out a few light strokes first. Price: £30.32 (Amazon UK) $29.75 in the USA. The Work Sharp Guided Field Sharpener is robust, has a lot of flexibility and is good value for money.